Now
- iPod board: final review fixes on the 6-layer logic board before ordering it.
- Proteus: finishing the thrust stand so we can measure the P8N motors and props before first flight.
- ETH, 3rd semester: Electronic Circuits, Signals and Systems I, Informatik II, Analysis 3.
- Learning: ESP32 firmware, ArduPilot, and how to test hardware without fooling myself.
Projects
-
A new logic board for the iPod 5th genNov 2026 → nowA drop-in board for the original iPod case, with an RP2350, a proper DAC, USB-C and the original click wheel. 6 layers, 193 parts, not ordered yet. -
ProteusOct 2026 → nowWith Davide. One wing for air and water. From 25 million concepts to the first flying prototype in six weeks; 32 steps logged, from CFD to wing prints. -
TS1 thrust standNov 2026A stand Davide and I laser-cut and built ourselves, with an ESP32 logger for thrust, rpm, current and temperature of the P8N motors. -
Learning and map layers on a world model of P8N. In simulation, final dive error fell from 38 m to under 7 m. -
Desk displayNov 2026A small screen next to my laptop for room climate, messages, a study timer and a to-do list. ESP32-S3, fed by a Mac service. -
Drone at the ETH Robotics ClubApr – Oct 2026Built a drone with the club. I worked on the hardware, maintenance and the flight controller.
-
iPod mod, built by handApr 2026An old iPod with new insides, wired by hand around a Raspberry Pi Zero 2 W. My own UI on Linux, Spotify through its API, and my WhatsApp messages on screen.
Learned
- PCB designiPod boardKiCad schematics, 6-layer layout, 0.8 mm board, stack-up planning, via-in-pad and fan-out, routing around a QFN-80 MCU, ERC / DRC to zero errors, autorouting with Freerouting, then finishing by hand, Gerbers, BOM and pick-and-place for JLCPCB, fitting a board to an existing case and connectors, 1:1 fit-check prints.
- Power and audio electronicsiPod board · iPod modLi-ion charging and boost (BQ25895), USB-C power and CC detection, buck converters and LDO rails, fuel gauges, load switches and hard-off, I2S audio and DAC choice (PCM510x, CS43131), headphone outputs, haptic drivers, circuit simulation in ngspice.
- Microcontrollers and embedded LinuxiPod mod · iPod board · Thrust stand · Desk displayRaspberry Pi Zero 2 W on Linux, RP2350 with PIO, PSRAM and flash, ESP32-S3 with PlatformIO and Arduino, PWM, interrupts and watchdogs, SPI displays, serial protocols over USB, background services (launchd).
- Software and APIsiPod mod · Desk display · Thrust standMy own music UI (retroDAP), Spotify Web API, forwarding phone messages to a device over Wi-Fi, Python tools and live dashboards, Git and GitHub, one branch per task.
- Sensors, testing and measurementThrust stand · ProteusLoad cells and calibration, optical rpm sensing, 1-Wire temperature sensors, current and voltage sensing, debugging with a multimeter, soldering and wiring harnesses, reading datasheets properly.
- Digital logic and FPGAsDigitaltechnik, ETHVerilog, iCEBreaker FPGA board with apio, testbenches, PWM (a glowing LED), reading a PDM microphone, Quartus and the DE1 board.
- Aerodynamics and flightProteusFlying wings and tailsitters, lift, drag and stall, static margin and neutral point, elevons and trim, hover, transition and cruise, motor and propeller matching, Pixhawk 6C and ArduPilot, flight-controller hardware and maintenance (ETH Robotics Club).
- Simulation and CFDProteusOpenFOAM, running jobs on the ETH Euler cluster (Slurm, containers), validating a model against known cases first, 6-DOF flight models, multi-objective optimisation (NSGA-II), Monte Carlo and uncertainty.
- Navigation and state estimationPositioningKalman filters (error-state EKF), sensor error models, dead reckoning, particle filters, magnetic and seabed map matching, learned corrections on top of physics.
- CAD and manufacturingProteus · Thrust stand · iPod boardFusion and SolidWorks, CAD generated from code, interference and clash checks, large PETG prints on a Prusa MK4S, designing parts in printable segments, laser cutting MDF with finger joints, test cuts to tune the slot fit, nesting parts on one sheet, restarting a cut that stopped, gluing, sanding and assembling flat-pack parts.
- Working with AI agentsProteus · iPod boardSplitting work into agent tasks, checking results with independent calculations, using other models as reviewers, knowing when a review loop stops helping, keeping facts in one data file.
Lessons
- Hardware that fails quietlyNov 2026On the thrust stand, signals and sensors looked fine in software while the hardware did something else. Measure at the real pin or wire, and change one thing at a time.
- Fixing the wrong layerNov 2026Under water the biggest errors came from physics and hardware, not from the algorithm. Find where an error really comes from before writing cleverer software.
- Outputs that go staleNov 2026A design changes, and the files made from it don't. Regenerate everything after every change, and keep each fact in one place.
- Trusting reviews too longNov 2026Reviews by people and AI helped a lot at first, then started going in circles. Check results independently, and stop a loop once it stops finding real problems.
- 3D printing large partsOct 2026Our wing prints failed again and again before the method worked. Print the riskiest part first, and only trust a check after it has caught a bad print.
- Believing the simulationOct 2026Models looked convincing but were wrong in places, and real parts weighed more than estimated. Test models against known cases, weigh real parts early, and build something that flies before adding more.
- Letting the optimiser cheatOct 2026Designs looked good only because something we computed was never checked. Every result an optimiser can influence needs a limit.
Experience
- Co-lead, ProteusOct 2026 →Run the project with Davide. Built the thrust stand with Davide; electronics, wing joint.
- Drone team member, ETH Robotics ClubApr – Oct 2026Hardware, maintenance and the flight controller of the club's drone.
Education
- B.Sc. Electrical Engineering and Information Technology, ETH Zürich2025 → 2028
- Abitur, Geschwister-Scholl-Gymnasium Gardelegen2025Advanced courses in physics, English and chemistry.
Notes
- Six weeks of Proteus2026-11-15
- more